Jump to content
Sign in to follow this  
Kingbong

Bho attempt

Recommended Posts

I've tasted sum cheese bho/shatter from cpt over the last week and damn its lekka. So now I gta try and make my own.. I've acquired an old boken lab measuring cylinder. Drilled a small hole at the base so that one of the butane nozzles can fit. This is the end product of the extractor.. As I progress I will update my experience. Does anybody know more or less how much cans of butane am I gna need for a tube this size.. Any advice welcome..a2959598e8ab7bf45a038c20c4d9863c.jpg9fae298f08b4cf8318f7c877f965338c.jpg

Share this post


Link to post
Share on other sites

From what I know it varies depending if you are using trim or bud. I think it comes down to how much oil there is for you to actually extract from the material you use. When the liquid coming out runs clean and clear then you know you done....Maybe have 2-3 just in case....? 

 

Made it once and we had an about 20g outdoor and used one can...dont think it wasnt finished and our cylinder was smaller than that

Share this post


Link to post
Share on other sites

This is jus to give it a go altho I'm not sure how I wil purge it cs I have no vac and its gna need a lot of bud.. Myt jus go for a smaller tube and make a small amount so I cn purge it in hot water. Dats been said to work well in small quantities of extract

 

Sent from my HUAWEI MT7-L09 using Tapatalk

 

 

Share this post


Link to post
Share on other sites
Guest kimcarsons

On the other hand. If you NEED to use that piece, just get a few sheets of wet/dry sandpaper and fillet (round) the sharp edge on the broken base. Aim for a radius of 3mm.

It should be good for a few uses.

 

 

 

Bad advice.

 

 

http://vapestore.co.za/other-stuff/bho-glass-tube The guy who owns the site use to be active on the weed.co.za forum

 

Good advice.

Share this post


Link to post
Share on other sites
Guest kimcarsons

KB, take the average of all responses and you'll still come up with the same. Don't do it. Skolley has wet ears and eager lips. 

Share this post


Link to post
Share on other sites
Guest kimcarsons

IMO this topic should be trashed. Poor extraction methods only lead to burning hair and crying children. Skolley, play as you will, but I don't think you should encourage/advise on something you clearly know very little about. You are an adult. Act like one and stfu when you don't know what you're talking about.

Share this post


Link to post
Share on other sites

If you wanna try a safe tube blah blah. Go buy a small Turkey baster  from crazy store.  Make sure to do it outside and have good air flow.. And remember kids

SAFETY FIRST.

 

Im on reaf's tip.. Stainless steel for the win.... Peasants use glass..

#SSporn

Share this post


Link to post
Share on other sites

Only if you are careless and maybe drop the tube, or hit it against another metal part. 

 

But you should think you are working in a Lab full of volatile chemicals and methodology should be precise.

Share this post


Link to post
Share on other sites
Guest kimcarsons

Skolley at least point out ALL the facts. Like that the cylinder breaking IS NOT THE MAIN CONCERN. When working with any flammable, it is highly recommended to use equipment designed for said purpose and always follow safety precautions. Butane in the atmosphere is highly flammable and should your vessel decide to direct the flow in any direction other than what you have intended, you are immediately compromising your safety. Simple as. No fear mongering, no masturbatory opi. Straight "facts" as you say. Oxygen, Hydrocarbons and an ignition source will result in flames and tears. Apply your logic to something like electricity. Wire it poorly and it might have nothing to do with any of the components or mechanism, simply a real world situation in which the theoretical limit of probability is met and you melt those golden locks right into the bone.

Share this post


Link to post
Share on other sites

First attempt at bho.... Any advice how i cud purge this further as I blasted into a a glass lid on warm water and kept the water warm until all the bubbling stopped. 1e1ed9dd020d47477f5bf213f4018428.jpg41b4b840bcb105bff007b9e075d18325.jpg47590f895b692cefb7794cb0acf4c758.jpg

Share this post


Link to post
Share on other sites

Tanx. I used 3g of dry bud and dat wat u c on d blade is wat I got out.. I tink I could of gotten more tho. Didn't run alot of butane, when I took off the coffee filter I seen alot of wat looked like kief.. Wil do another run wit one of the bigger tubes to c wat I cn get out but apparently the more u extract is proportional to the more the need for a vacuum purging set up. 

 

Sent from my HUAWEI MT7-L09 using Tapatalk

 

 

Share this post


Link to post
Share on other sites
Guest kimcarsons

No. you can run kilos of tane through your material, all that you'll do is waste tane. Run the tane till it goes clear, then it is done. Purge on a low heat for a loooong time. Read up on boiling temps of the tane to decide on your sweet spot. Also remember that butane is the least of the issues with residue. It is usually the heavier mercaptans that stay behind. Keep it clean, keep it simple and don't try reinvent an already obsolete technique.

Share this post


Link to post
Share on other sites

I've read of ppl blasting directly into water. I wil give a few different methods a try. N c which works best for me

 

Sent from my HUAWEI MT7-L09 using Tapatalk

 

 

Share this post


Link to post
Share on other sites

I don't like blasting into water.

As a hydrocarbon it pulls  alot of water with it. So your product will end up waxing up or just crackling when dabbed...

 

But yes try it and you will know..

Share this post


Link to post
Share on other sites

I did another run with some outdoor c99.. Literally see through wen settled. Kept it on a 40°C water bath stiring  Took bout 30mins to c no bubbles

 

c1c7e75d61a0aaab832b0ddb8470245c.jpg

 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×