Author Topic: Bho attempt  (Read 1003 times)

Offline Kingbong

  • Seedling
  • *
  • Posts: 49
  • Thanked: 1 times
Bho attempt
« on: February 19, 2016, 01:34:51 PM »
I've tasted sum cheese bho/shatter from cpt over the last week and damn its lekka. So now I gta try and make my own.. I've acquired an old boken lab measuring cylinder. Drilled a small hole at the base so that one of the butane nozzles can fit. This is the end product of the extractor.. As I progress I will update my experience. Does anybody know more or less how much cans of butane am I gna need for a tube this size.. Any advice welcome..
 

Offline cheese420

  • Vegging Bush
  • ***
  • Posts: 303
  • Thanked: 12 times
Re: Bho attempt
« Reply #1 on: February 19, 2016, 02:24:05 PM »
From what I know it varies depending if you are using trim or bud. I think it comes down to how much oil there is for you to actually extract from the material you use. When the liquid coming out runs clean and clear then you know you done....Maybe have 2-3 just in case....? 

Made it once and we had an about 20g outdoor and used one can...dont think it wasnt finished and our cylinder was smaller than that
 

kimcarsons

  • Guest
Re: Bho attempt
« Reply #2 on: February 19, 2016, 02:29:00 PM »
Buy a tube.
 

Offline Dabtzar

  • Maturing
  • *****
  • Posts: 730
  • Thanked: 32 times
  • *****420/710*****
Re: Bho attempt
« Reply #3 on: February 19, 2016, 04:17:28 PM »
Safety first man..

Read the other threads on here about bho.

Newport only
 

Offline Green Leaf Organics

  • Switched Over
  • ****
  • Posts: 584
  • Thanked: 47 times
Re: Bho attempt
« Reply #4 on: February 19, 2016, 04:22:20 PM »
Agree with the other... I would be worried about that tube , will be very risky. Personally I use a marine grade stainless steel tube
 

Offline cheese420

  • Vegging Bush
  • ***
  • Posts: 303
  • Thanked: 12 times
Re: Bho attempt
« Reply #5 on: February 19, 2016, 04:24:18 PM »
http://vapestore.co.za/other-stuff/bho-glass-tube

The guy who owns the site use to be active on the weed.co.za forum
 

Offline Green Leaf Organics

  • Switched Over
  • ****
  • Posts: 584
  • Thanked: 47 times
Re: Bho attempt
« Reply #6 on: February 19, 2016, 04:46:29 PM »
The give exellent service and have good products
 

Offline Kingbong

  • Seedling
  • *
  • Posts: 49
  • Thanked: 1 times
Re: Bho attempt
« Reply #7 on: February 19, 2016, 05:25:29 PM »
This is jus to give it a go altho I'm not sure how I wil purge it cs I have no vac and its gna need a lot of bud.. Myt jus go for a smaller tube and make a small amount so I cn purge it in hot water. Dats been said to work well in small quantities of extract

Sent from my HUAWEI MT7-L09 using Tapatalk

 

kimcarsons

  • Guest
Re: Bho attempt
« Reply #8 on: February 19, 2016, 06:10:19 PM »
On the other hand. If you NEED to use that piece, just get a few sheets of wet/dry sandpaper and fillet (round) the sharp edge on the broken base. Aim for a radius of 3mm.
It should be good for a few uses.



Bad advice.

 
http://vapestore.co.za/other-stuff/bho-glass-tube The guy who owns the site use to be active on the weed.co.za forum

Good advice.
 

kimcarsons

  • Guest
Re: Bho attempt
« Reply #9 on: February 20, 2016, 12:08:50 AM »
KB, take the average of all responses and you'll still come up with the same. Don't do it. Skolley has wet ears and eager lips. 
« Last Edit: February 20, 2016, 12:13:16 AM by kimcarsons »
 

kimcarsons

  • Guest
Re: Bho attempt
« Reply #10 on: February 20, 2016, 12:17:56 AM »
IMO this topic should be trashed. Poor extraction methods only lead to burning hair and crying children. Skolley, play as you will, but I don't think you should encourage/advise on something you clearly know very little about. You are an adult. Act like one and stfu when you don't know what you're talking about.
 

Offline Dabtzar

  • Maturing
  • *****
  • Posts: 730
  • Thanked: 32 times
  • *****420/710*****
Re: Bho attempt
« Reply #11 on: February 20, 2016, 07:21:38 AM »
If you wanna try a safe tube blah blah. Go buy a small Turkey baster  from crazy store.  Make sure to do it outside and have good air flow.. And remember kids
 SAFETY FIRST.

Im on reaf's tip.. Stainless steel for the win.... Peasants use glass..
#SSporn
 

Offline Dabtzar

  • Maturing
  • *****
  • Posts: 730
  • Thanked: 32 times
  • *****420/710*****
Re: Bho attempt
« Reply #12 on: February 20, 2016, 02:04:05 PM »
Only if you are careless and maybe drop the tube, or hit it against another metal part. 

But you should think you are working in a Lab full of volatile chemicals and methodology should be precise.
 

Offline Dabtzar

  • Maturing
  • *****
  • Posts: 730
  • Thanked: 32 times
  • *****420/710*****
Re: Bho attempt
« Reply #13 on: February 21, 2016, 07:24:56 AM »
Or you go to the other extreme and get Super Critical Co2....  Lol
 

kimcarsons

  • Guest
Re: Bho attempt
« Reply #14 on: February 21, 2016, 11:45:07 AM »
Skolley at least point out ALL the facts. Like that the cylinder breaking IS NOT THE MAIN CONCERN. When working with any flammable, it is highly recommended to use equipment designed for said purpose and always follow safety precautions. Butane in the atmosphere is highly flammable and should your vessel decide to direct the flow in any direction other than what you have intended, you are immediately compromising your safety. Simple as. No fear mongering, no masturbatory opi. Straight "facts" as you say. Oxygen, Hydrocarbons and an ignition source will result in flames and tears. Apply your logic to something like electricity. Wire it poorly and it might have nothing to do with any of the components or mechanism, simply a real world situation in which the theoretical limit of probability is met and you melt those golden locks right into the bone.